信龍濾清器產品特點：
1、分高壓段用、中壓段用、回油段用和吸油段用
2、分高中低精度等級。2—5um為高精度，10—15um為中等精度，15—25um為低精度。
3、為壓縮濾芯成品外形尺寸，增大過濾面積，一般濾層部分折成波紋狀，液壓濾芯打褶高度一般在20㎜以下
4、液壓濾芯承受壓差一般在0.35—0.4mpa，但個別特殊濾芯，要求承受高壓差，最高要求承受32mpa，甚至42mpa等同系統壓力。
5、最高承受溫度，有的要求達到135℃
產品要求：
1、強度要求，制作完整度要求、承受壓差、承受安裝外力、承受壓差交變載荷
2、通油的順暢度要求，流量阻力特性
3、耐一定的高溫，與工作介質相容
4、濾層纖維不能位移和脫落
5、成承載較多的污物
6、高空及寒冷地區使用正常
7、耐疲勞，交變流量下的疲勞強度
8、濾芯本身清潔度要達標
測試標準：
（1）iso2942液壓傳動-濾芯-結構完整性的測定
（2）iso16889液壓傳動-過濾器-測定過濾特性的多次通過法
（3）iso3968液壓傳動-過濾器-壓降流量特性的測定
（4）iso3724液壓傳動-濾芯-流動疲勞特性的測定
（5）iso3723液壓傳動-濾芯-軸向載荷試驗方法
（6）iso2943液壓傳動-濾芯-材料與液體相容性的驗證
（7）iso2941液壓傳動-濾芯-抗破裂性的驗證
液壓濾芯的更換時間：
液壓挖掘機一般在運轉2000h以后就需要更換液壓油，否則將使系統污染，造成系統故障。據統計，液壓系統的故障中90%左右是由于系統污染所造成的。
在檢查油品的顏色、黏度、氣味的基礎上，還要檢測機油壓力、空氣濕度。若工作在海拔較高、溫度較低的環境，還必須密切注意發動機機油里含炭量、膠質物(烯烴)和硫化物，以及柴油里的雜質、石蠟和水分的含量。
特殊情況，若機械使用低等級柴油(柴油中含硫量0.5﹪～1.0﹪)，應每隔150h更換一次柴濾、機濾;含硫量在1.0﹪以上應每隔60h更換一次柴濾、機濾。使用破碎器、振動夯等對液壓系統負荷較大的設備，液壓回油濾芯、先導濾芯和呼吸器濾芯的更換時間為每隔100h更換一次。
HYDAC 0160 D 100 W/HC /-WHYDAC 0630 DN 025 W/HCHYDAC 0110 D 003 V /-W10、熱力、化工管線保溫，保溫隔熱效果優于一般保溫材料。HYDAC 0100 MX 020 BN4HC /-B1.7HYDAC 0280 D 010 MMHYDAC 0030 R 005 BN4HC /-KBHYDAC 0280 D 100 W/HC /-V(5)粉塵沉積形態與纖維容塵負荷；HYDAC 0250 DN 006 BH4HCHYDAC 0040 DN 006 BN4HCHYDAC 0990 D 020 BN4HC
HYDAC 0160 D 020 VThe Bidder/Buyer agrees to assume all responsibility and risk regarding the safety, suitability of use and legal requirements concerning ownership, storage, installation, operation and use of the Item and to hold Seller harmless and free of all liability regarding the safety, condition, usability, installation, use, maintenance, disposal, legality and suitability of use and any other issues regarding this Item. Item is an industrial use product intended for installation and use by qualified personnel and can cause injury or damage if improperly used or installed. Most Items, including but not limited to, those labeled as “Explosion Proof” or suitable for installation in “Hazardous Locations,” require the use of appropriate installation materials and techniques in order to insure a proper and safe installation. Proper and safe installation and operation of the Item, including compliance with applicable electrical, plumbing, fire, safety and other codes, is the sole responsibility of the Buyer. Seller is not responsible for the accuracy of any safety, operation or maintenance instructions or literature that may be (when available) provided to Buyer by Seller with this Item. Buyer is urged to consult the original manufacturer of the Item for installation, safety, maintenance and operating instructions which may also be available online at the manufacturer’s website. In any and all cases, Seller's liability is limited to the amount of the winning bid paid and does not include any direct, indirect, incidental or miscellaneous damages, or any other damages, inconveniences, costs or expenses.HYDAC 0450 D 003 BH4HCHYDAC 0100 MX 020 ECON2 /-B1.7HYDAC 0280 D 003 BH4HCHYDAC 0060 D 003 BH4HCHYDAC 0060 D 020 V /-VHYDAC 0165 L 003 P
在線咨詢 
